leko-pona/README.md

# leko pona
![](images/leko_tonsi.png)

![](images/leko-pona.png)

## Related repos
- <a href = "/CrispyPin/zmk-config/">ZMK config</a> (layout based on colemak-dh)
- [Ergogen config](https://github.com/CrispyPin/ergogen/) used to generate the pcb

## Parts list
- nice!nano x2
- 12 pin socket strips x4
- JST-PH battery connectors x2
- PCM12 power switch x2
- 3.7V 130mAh battery x2
- choc switches x36
- choc keycaps x36
- choc hotswap sockets x36 (optional)
- rubber feet (optional)

## Notes about assembly
- Solder pads for the reversible footprint should be soldered on the underside of the board if you want the back of the nice!nano facing up (like in the picture)
- The battery connector is slightly asymmetrical on the two halves, it should be clear from the outline on the silkscreen which way to put it
- If your batteries are small enough you can tuck them under the controllers
- You can use a permanent marker to get a clean look on the edges of the pcbs

![](images/battery.png)

## LEGO tenting set
[Instructions](lego_tenting.md)

![](images/tenting.png)
add pcb files 2022-10-01 12:07:38 +02:00			`# leko pona`
add new image 2023-08-26 15:52:10 +02:00			`![](images/leko_tonsi.png)`
add pcb files 2022-10-01 12:07:38 +02:00
Update README.md 2022-10-01 12:19:20 +02:00			`![](images/leko-pona.png)`

			`## Related repos`
make zmk config link relative 2024-04-18 22:12:34 +02:00			`- <a href = "/CrispyPin/zmk-config/">ZMK config</a> (layout based on colemak-dh)`
Update README.md 2022-10-01 12:19:20 +02:00			`- [Ergogen config](https://github.com/CrispyPin/ergogen/) used to generate the pcb`
add pcb files 2022-10-01 12:07:38 +02:00
Add part list and assembly notes to readme 2022-10-21 12:55:42 +02:00			`## Parts list`
			`- nice!nano x2`
			`- 12 pin socket strips x4`
			`- JST-PH battery connectors x2`
			`- PCM12 power switch x2`
			`- 3.7V 130mAh battery x2`
			`- choc switches x36`
			`- choc keycaps x36`
			`- choc hotswap sockets x36 (optional)`
			`- rubber feet (optional)`

			`## Notes about assembly`
			`- Solder pads for the reversible footprint should be soldered on the underside of the board if you want the back of the nice!nano facing up (like in the picture)`
			`- The battery connector is slightly asymmetrical on the two halves, it should be clear from the outline on the silkscreen which way to put it`
			`- If your batteries are small enough you can tuck them under the controllers`
Update README.md 2022-10-31 12:52:01 +01:00			`- You can use a permanent marker to get a clean look on the edges of the pcbs`
Add part list and assembly notes to readme 2022-10-21 12:55:42 +02:00
			`![](images/battery.png)`
add lego tenting set instructions 2022-10-26 21:00:25 +02:00
			`## LEGO tenting set`
			`[Instructions](lego_tenting.md)`

			`![](images/tenting.png)`